Gate Repair in Keene, TX
Gate repair in Keene, TX typically runs $180-$650, with most hinge, post, and realignment jobs finished in a single visit. Keene isn’t a typical subdivision town: the work here splits between heavy pipe-rail livestock gates on acreage and institutional campus gates near Southwestern Adventist University, with Johnson County’s shifting black clay driving more post work than anywhere else in the area. Call (833) 754-7503 and a live person answers, any hour, any day.
Why Keene Homes Are Different
Johnson County sits on expansive black clay that swells after spring rains and shrinks through summer drought. That cycle heaves gate posts out of plumb, which is why so many Keene gates drag the ground even when the gate itself is fine. The housing mix adds another layer: modest mid-century homes near the SWAU campus carry original wrought iron that needs restoration welding, while surrounding acreage properties have working livestock pens with gates that take real abuse. The Saturday Sabbath observance also shapes scheduling here, and we respect it.
Gate Repair in Keene
Gate repair in Keene comes down to the actual load. A 400-pound pipe-rail cattle gate off Old Betsy Road needs different hinges, posts, and opener tuning than a decorative driveway gate in a subdivision. We stock heavy-duty hardware and parts for the nine automation brands we service, so most repairs finish in one trip. Our Gate Repair work here covers everything from a sagging hinge to a motor that’s been fighting a twisted post.
Post Repair
Post repair is the single most common job we do in Keene. The black clay under 76059 swells in spring and shrinks in August, tilting posts that were plumb six months earlier. We don’t just shim a leaning post: we excavate, re-plumb with a level, and reset with concrete belled footings and bracing sized for the gate. Post re-plumbing and reset runs $340-$650 in Keene because the clay demands deeper excavation and wider footings than sandy-soil regions need.
Hinge Repair
Heavy pipe-rail gates destroy standard residential hinges. We’ve pulled pin-style hinges off Keene livestock gates that were bent into S-shapes because the hardware was rated for a 150-pound decorative gate, not a 600-pound working one. We measure gate weight, post deflection, and swing arc, then spec the right hinge barrel and pin diameter. Hinge replacement runs $180-$290 for standard duty, and $260-$420 when we upgrade to heavy-duty fabricated strap hinges sized for the actual load.
Gate Realignment
A gate that drags or binds at the latch is usually a geometry problem, not a gate problem. In Keene, the geometry changes seasonally as posts shift in the clay. We measure post-to-post width at three heights, check for frame twist, and adjust or shim hinges to restore the swing. If the posts have moved, realignment alone is temporary. We’ll tell you that before we start. Realignment without post work runs $150-$240.
Do you repair heavy cattle gates on acreage properties near Keene?
Yes. We specialize in the working pipe-rail gates common on Keene’s rural properties, with hinge hardware and post bracing rated for gates of 300 pounds or more. The black clay soil shifts concrete footings seasonally, so we reset posts with deeper footings and steel bracing. Call (833) 754-7503 for an exact quote, estimates are free.
Gate Installation in Keene
Gate installation in Keene typically runs $2,800-$7,500, with livestock-grade swing systems on rural acreage reaching the higher end. The clay soil means posts must go 42-48 inches deep with 12-inch diameter footings to stay below the active heave layer. Our Gate Installation team fabricates gates that match existing welded pipe fencing, whether it’s bare steel, galvanized, or painted.
Swing Gate Installation
A well-built single swing gate handles livestock traffic, equipment access, and daily use without track maintenance. On acreage near Kings Crest Drive and throughout 76059, we regularly see pipe-rail gates weighing 400-600 pounds, where light-duty residential hardware fails within months. Single swing installations run $2,800-$4,200 for standard residential, and $4,500-$7,500 when the job calls for livestock-grade hinges, commercial openers, and deep footings.
Double Gate Installation
Double gates split a wide opening into two leaves, but they need synchronization: both leaves must swing freely, meet flush, and latch cleanly even after the ground shifts. We include adjustable center stops, heavy-duty drop rods for the inactive leaf, and openers sized for the combined weight. Too many Keene doubles were installed with standard residential openers on 16-foot spans, and the motors burned out within a couple of years.
Can you install a gate on my property without disturbing my Saturday observance?
Yes. We do not schedule installations, follow-up visits, or proactive outreach on Saturdays in Keene, out of respect for the local Sabbath observance. Weekend installation availability is Sunday or any weekday. Call (833) 754-7503 to arrange whatever day works for you, and we’ll confirm scheduling that respects your preference.
Gate Motor & Opener in Keene
Gate motor and opener work in Keene runs $280-$650 for most residential repairs, with heavy-duty acreage systems reaching $1,100-$1,400 when a full commercial installation is needed. The real issue on Keene acreage is overload: residential openers that were never rated for 500-pound livestock gates burn out fast. Our Gate Motor & Opener team carries parts for all nine brands we service.
Motor Installation
We size the motor to the gate, not the other way around. A 16-foot welded pipe-rail gate needs a different opener than a 12-foot aluminum decorative one. New motor installation runs $450-$890 for standard residential systems and $1,100-$1,400 for heavy-duty commercial openers on acreage gates. For rural Keene properties where power reliability fluctuates, we spec battery backup on every installation.
Motor Repair
Most motor repairs in Keene fall between $180 and $340. Common failures include stripped clutch assemblies from gates dragging in shifted clay, burned circuit boards from overloaded residential openers, and seized linear actuators from dust and debris. We carry parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule on the truck. One visit, gate working, bill settled before we leave.
Why do gate motors on acreage properties near Keene fail more often than in the suburbs?
Heavier gates, harsher cycles, and the expansive black clay combine to overload motors that were never sized for the load. A Keene pipe-rail livestock gate can weigh 500 pounds and cycle twenty times daily. The motor runs hotter, the clutch wears faster, and when the clay heaves the post, the gate drags and the motor fights it. Call (833) 754-7503 for a load assessment.
Gate Access Control in Keene
Gate access control in Keene runs $280-$650 for most keypad, remote, or phone entry work. The two recurring local problems are moisture intrusion from clay-heaved posts and voltage drop on long wire runs to remote gates. Our Gate Access Control team services keypads, intercoms, card readers, and phone entry systems for properties throughout 76059.
Keypad Entry Systems
Keypad entry is the workhorse of rural Keene properties, and it’s where we see the most weather-related failures. The clay soil traps moisture against posts that settle every season, corroding keypad circuits from the inside. Keypad entry repair runs $180-$340, and full replacement runs $320-$580, including new underground conduit where the old wire has cracked from soil movement.
Phone Entry Systems
Phone entry on Keene acreage faces a specific challenge: power. When the gate sits far from the house’s main panel, voltage drop and intermittent power loss are common, especially during summer drought when ground rods loosen in shrinking soil. Phone entry installation runs $450-$780. We size wire gauges for the actual run length and install dedicated transformers where needed.
Can you install a keypad on a ranch gate that’s far from my house in Keene?
Yes. We run underground conduit below the active clay zone to prevent seasonal heave from cracking wires, and we size transformers for the actual distance, not a suburban assumption. A remote keypad installation in Keene runs $320-$580. Call (833) 754-7503 and we’ll walk through your gate’s location and power options.
Gate Parts & Welding in Keene
Gate parts and welding in Keene runs $180-$650 for most jobs, and our trucks carry heavy-duty hinges, schedule 40 steel posts, and welding equipment. The work here often means fabricating hardware that a catalog doesn’t carry: custom strap hinges for 600-pound cattle gates, belled concrete footings for shifting clay, and rail repairs that match existing pipe. Our Gate Parts & Welding service is built for exactly this.
Hinge Replacement
Standard homeowner-grade hinges fail fast on Keene’s heavier gates. A 14-foot pipe-rail livestock gate off FM 2280 can weigh 600 pounds or more, and big-box pin hinges aren’t rated for that. We fabricate heavy-duty strap hinges with grease fittings and thrust bearings, sized to the actual gate weight. Standard hinge replacement runs $180-$280, and custom heavy-duty fabrication runs $280-$420.
Post Replacement
Johnson County’s black clay swells and shrinks every season, heaving gate posts two to four inches out of plumb. Post replacement in Keene isn’t just digging a hole: we remove the old post, excavate to 48 inches minimum, and set schedule 40 steel with concrete belled footings that resist the uplift. Single post replacement with a concrete footing runs $340-$650.
Can you make custom heavy-duty hinges for livestock gates in Keene?
Yes. We fabricate strap hinges rated to 800 pounds with grease fittings and thrust bearings, sized to your gate’s actual weight and swing geometry. Standard catalog hinges fail on working livestock gates. Most custom hinge jobs run $280-$420 and finish in one visit. Call (833) 754-7503 for a free estimate.
Brands We Service in Keene
We’re certified on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most repair parts are stocked on the truck. See our brands for the full list.
Pricing for Gate Repair in Keene, TX
| Service | Typical Range in Keene |
|---|---|
| Hinge repair or replacement (residential) | $180-$290 |
| Hinge upgrade for heavy farm/livestock gate | $260-$420 |
| Post re-plumbing and reset | $340-$650 |
| Gate realignment (no post work) | $150-$240 |
| Weld repair, frame crack | $180-$320 |
| Motor repair (residential swing/slide) | $180-$340 |
| New motor installation (standard residential) | $450-$890 |
| Keypad entry installation/replacement | $320-$580 |
Post work runs higher in Keene because the black clay demands deeper excavation, wider footings, and steel bracing that sandy-soil regions don’t need. The price we quote is the price you pay, settled before any work begins.
Neighborhoods We Serve in Keene
Our service radius covers all of 76059 and the surrounding Johnson County acreage. Most calls get a same-visit dispatch from our Dallas-Fort Worth office, with repair response typically within an hour.
- Campus vicinity (SWAU area)
- Old Betsy Road corridor
- FM 2280 east of town
- Central Keene (mid-century homes)
Service Area - Cities Near Keene
Ironworks Gate Co. serves Keene, TX and the surrounding Johnson County communities, including Cleburne, TX, Joshua, TX, Burleson, TX, Crowley, TX, and Rendon, TX. The same crews and the same 90-Day Done Right Promise apply across the whole service area.
Serving Keene, TX - Our Local Coverage Area
Ironworks Gate Co. crews serve Keene and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Keene coverage area; if your address is on it, we can help.
Also serving nearby: Keene, TX, Cleburne, TX, Joshua, TX, Burleson, TX, Crowley, TX, Rendon, TX.
FAQs About Gate Repair in Keene
Most repair calls in Keene get a same-day response, typically within an hour, because our Dallas-Fort Worth office dispatches crews directly to Johnson County. Sunday emergency calls are staffed for the local Sabbath observance pattern. Call (833) 754-7503 and a live person answers immediately.
Most gate repairs and replacements on existing posts don’t require a permit in Keene. New installations with concrete footings or adding access control wiring may trigger a simple permit review, which we handle as part of the job. Call (833) 754-7503 and we’ll check the specific requirements for your property.
Call Ironworks Gate Co. at (833) 754-7503 for a free estimate on any gate repair, installation, motor, access control, or welding job in Keene. A live person answers 24 hours a day, 7 days a week, and every job is backed by our written 90-Day Done Right Promise.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Keene Customers Say
"The hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a new gate, which two other companies had pushed for."
- Megan Whitaker"Reprogrammed every clicker in the community and set up the keypad codes. Patient with a very long list of residents."
- Devon Ingram"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one on the truck, and we were moving cars again inside an hour."
- Chris Gallagher