Gate Repair in Cleburne, TX
Gate repair in Cleburne typically runs $180 to $650 depending on whether you need a hinge adjusted, a post reset, or full welding work, and most jobs wrap up in a single visit with the price settled before we start. Cleburne sits on Blackland Prairie clay that shrinks in drought and heaves after rain, which means leaning posts and binding gates show up here more than almost anywhere else in Johnson County. If your gate is dragging, sagging, or refusing to open, call (833) 754-7503 and we’ll send a technician who knows this ground.
Why Cleburne Homes Are Different
Most Cleburne homes sit on expansive black clay that moves inches vertically every year. Summer drought pulls moisture out and the soil shrinks back. A hard rain swells it upward. That slow cycle torques gate posts out of plumb, stresses weld joints, and throws automatic openers out of alignment. Add the February 2021 ice event that seized gearboxes and cracked plastic sensor housings across the county, and you have a repair market unlike the suburban neighborhoods north of here. Near the historic downtown core, early-1900s homes often have original wrought-iron pedestrian gates that need careful weld repair. Along the 76031 and 76033 corridors, 1980s-to-2000s ranch homes on larger lots run iron swing gates at long driveway entrances. South and west of town along FM 2280 and FM 917, acreage properties use agricultural pipe-frame gates that drag caliche drives when their posts walk out of the clay.
Gate Repair in Cleburne
Gate repair in Cleburne spans two worlds: ornamental iron on in-town homes and heavy pipe gates on acreage. Both fail here for the same root reason: the clay under the posts will not hold still. We fix the post first, then the gate, then recalibrate the opener. A patch job on a leaning post lasts one season. A proper reset lasts decades.
Post Reset and Stabilization
On properties along FM 2280 and FM 917, we regularly see agricultural pipe-frame swing gates set directly in clay with no concrete footing. After a few wet seasons the posts walk out of the ground and the gate drags the caliche drive. We excavate, dig a 4-foot minimum footing, set the post in concrete with rebar, and rehang the gate. A single post reset in Cleburne typically runs $280 to $520 depending on depth and access.
Weld Repair on Iron and Pipe Gates
Freeze-thaw cycles and constant clay torque crack welds at hinges and latch points, especially on older ornamental work near downtown and on agricultural gates without footings. We grind, prep, weld to structural standard with 7018 rod, then prime and paint to match. Weld repair in Cleburne runs $180 to $340 for most residential and light agricultural gates, and $220 to $550 for extensive structural work. Our full Gate Repair scope covers hinges, latches, tracks, rollers, and rust treatment.
How much does gate repair cost in Cleburne?
Most gate repairs in Cleburne fall between $180 and $650 depending on the problem. Hinge work runs $140 to $290, realignment $180 to $340, post resetting $280 to $520, and weld repair $220 to $550. The price is settled before we start and never changes mid-job. Call (833) 754-7503 for an exact quote, estimates are free.
Gate Installation in Cleburne
Gate installation in Cleburne means building for clay that moves, wind that gusts across open prairie, and freezes that crack undersized hardware. Most residential and small-acreage installs run $2,800 to $7,500, with the full price settled before we dig the first post hole. Our Gate Installation work includes everything from ornamental iron pedestrian gates to heavy automated ranch gates, all spec’d for this soil.
Double Swing Gates for Acreage
Double gates suit the 14-to-20-foot driveway entrances common on Cleburne acreage. We recently installed one off FM 2280 where the previous setup had pulled out of the clay after two wet seasons. Our crew dug 48-inch footings, set the posts in concrete, and matched the opener to the actual gate weight rather than the brochure spec. A double swing driveway gate with automation in Cleburne typically runs $4,200 to $6,800.
Pedestrian and Ornamental Iron Gates
For homes near the historic downtown core, ornamental iron or aluminum swing gates with traditional scrollwork fit the original architecture. We match existing fence lines and tuck the operator housing where it won’t dominate the entry. A manual ornamental pedestrian gate in Cleburne runs $1,800 to $2,800 installed, and an automated single swing driveway gate runs $2,800 to $4,500.
What type of gate is best for a historic home near downtown Cleburne?
Ornamental iron or aluminum swing gates with traditional scrollwork and finials suit the early-1900s homes near Buffalo Street and the courthouse square. We match the existing fence line and integrate automation in a compact operator housing that doesn’t overpower the pedestrian-scale entry. Call (833) 754-7503 to review styles and get an exact quote.
Gate Motor & Opener in Cleburne
Gate motor repair in Cleburne runs $180 to $450 for most jobs, and many are completed same-day. The motor is rarely the root cause here. When the clay shifts and the post tilts even a few degrees, the opener binds, overamps, and burns out limit switches or gears. We fix the alignment first, then repair or replace the motor. Our Gate Motor & Opener service covers all major brands.
Linear Motor Service
Linear arm operators are common on Cleburne’s ornamental swing gates, and they’re especially vulnerable to post movement. When black clay shrinks in August and a post tilts three degrees, the arm binds and the motor burns through limit switches. On homes along the 76031/76033 boundary and near Country Club Road, we see this pattern every dry season. A new linear motor installed correctly in Cleburne runs $650 to $1,100.
Motor Repair and Gearbox Replacement
Hard freezes like February 2021 seized gearboxes and cracked plastic housings across Johnson County. We flush and repack with cold-rated lubricant or replace with freeze-rated models. Most motor repairs in Cleburne fall between $180 and $450, including diagnostic, parts, and labor. A heavy-duty slide motor replacement for agricultural gates runs $1,400 to $2,400.
Why do gate motors fail after a wet spring in Cleburne?
The clay absorbs spring rainfall and swells upward, tilting posts and binding motors that were aligned during dry weather. We see a spike in calls every April and May, especially from acreage properties south of town. If your gate started grinding after rain, the post probably moved. Call (833) 754-7503 and we’ll check the plumb.
Gate Access Control in Cleburne
Gate access control in Cleburne runs $180 to $650 depending on the system, and most jobs finish in one visit. Whether you need a keypad at the property line, a remote reprogrammed, or a phone entry system for a rural parcel, we carry parts for nine major brands and settle the price before work starts. Our Gate Access Control work covers keypads, remotes, intercoms, and card readers.
Keypad Entry Systems
For homes along the 76031 and 76033 corridors with long driveways, a weather-rated keypad at the property line saves repeated trips to the gate. We install wired and wireless units rated for North Texas sun and hard freeze conditions, using metal housings rather than plastic consumer models. A typical keypad installation in Cleburne runs $280 to $450 including mounting and wiring.
Phone Entry Systems
On larger rural parcels west of Cleburne, phone entry lets a delivery driver or family member call your cell from the gate and you buzz them in. We install cellular-based systems that don’t require a buried phone line, which matters where trenching runs into shallow rock. Phone entry installation in Cleburne runs $480 to $780, with cellular models at the higher end. Every job carries the 90-Day Done Right Promise in writing.
Can I retrofit a smart access system to an older LiftMaster opener in Cleburne?
Most LiftMaster operators made after 2005 can accept a modern smart module or WiFi keypad with a compatible receiver board. We verify the model and control board on the first visit, and if the board is too old we quote the upgrade before proceeding. Retrofits in Cleburne run $320 to $580. Call (833) 754-7503 for a free check.
Gate Parts & Welding in Cleburne
Gate parts and welding in Cleburne runs $180 to $650 depending on whether you need a hinge swapped, a post reset, or a full rail weld. Most jobs finish in one visit with the price settled before we strike an arc. The clay here moves constantly, and that movement ends up expressed in cracked welds, torn hinge plates, and posts that will not stand straight. Our Gate Parts & Welding shop handles it all, from decorative scrollwork on in-town iron to heavy structural repair on ranch gates.
Post Replacement with Concrete Footer
Post replacement in Cleburne is almost always about the clay. We replaced a post on a ranch off FM 2280 where a heavy steel swing gate had pulled its post out of the ground after a wet spring. The fix was a 4-foot-deep concrete footer with rebar, sized to the gate weight and wind load. Post replacement with a concrete footer in Cleburne runs $350 to $650.
Hinge Replacement and Rail Repair
Binding hinges are usually the first sign a post is going out of plumb. We stock adjustable hinge brackets that compensate for minor post movement, plus heavy-duty ball-bearing hinges for agricultural gates that see daily use. Hinge replacement in Cleburne runs $180 to $340. Rail repair, whether steel or wood, runs $200 to $400.
Can you replace just the hinge on a 20-foot pipe gate in Cleburne?
Yes, if the post is still plumb and the frame isn’t twisted. We stock ball-bearing hinges rated for agricultural loads and weld new plates if the old ones have torn. If the post has leaned, hinge-only is wasted work, we’ll tell you straight. Call (833) 754-7503 for an honest assessment.
Brands We Service in Cleburne
We’re trained and equipped on nine gate-automation brands, including Linear, Viking, Ghost Controls, and DoorKing. We stock common parts locally for faster turnaround in Cleburne, and whatever is on your driveway, we have the manual and the tooling. See our brands for the full list.
Pricing for Gate Repair in Cleburne, TX
| Service | Typical range in Cleburne |
|---|---|
| Hinge repair / replacement | $140 - $290 |
| Gate realignment | $180 - $340 |
| Weld repair | $180 - $550 |
| Post reset or replacement | $280 - $650 |
| Gate motor / opener repair | $180 - $450 |
| Keypad entry installation | $280 - $450 |
| Phone entry system installation | $480 - $780 |
| Full gate replacement (installed) | $1,800 - $7,500 |
What pushes the price upward in Cleburne is almost always the footing. Deeper concrete work for shifting clay, recalibration after post movement, and welding access on tight in-town lots all move the number. The price is settled before we start, and it does not change when the job is done.
Neighborhoods We Serve in Cleburne
We work across both Cleburne ZIP codes, 76031 and 76033, with typical drive time under 30 minutes to any address in the city limits or the immediate rural fringe. Most repair calls get same-day or next-day response.
- Historic Downtown Cleburne
- Westhill / Hillcrest area
- FM 2280 corridor
- FM 917 corridor
- Country Club Road area
Service Area - Cities Near Cleburne
We serve Cleburne, TX and the surrounding Johnson County communities, with dispatch coordinated from our DFW office. That includes Keene, TX, Joshua, TX, Burleson, TX, Crowley, TX, and Rendon, TX. Same crew, same 90-Day Done Right Promise, same live person answering the phone.
Serving Cleburne, TX - Our Local Coverage Area
Ironworks Gate Co. crews serve Cleburne and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Cleburne coverage area; if your address is on it, we can help.
Also serving nearby: Cleburne, TX, Keene, TX, Joshua, TX, Burleson, TX, Crowley, TX, Rendon, TX.
FAQs About Gate Repair in Cleburne
Most repair calls in Cleburne get same-day or next-day response, with drive time under 30 minutes to any address in the 76031 or 76033 ZIP codes. A live person answers the phone 24/7, and we’ll give you a straight arrival window when you call. Reach us at (833) 754-7503.
Most gate repairs and replacements on existing posts don’t require a city permit in Cleburne, but larger installations with new footings or electrical runs may. We handle the local requirements on every job and we’ll tell you upfront if anything needs filing before work starts. Call (833) 754-7503 and we’ll check your specific situation.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Cleburne Customers Say
"The hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a new gate, which two other companies had pushed for."
- Megan Whitaker"Reprogrammed every clicker in the community and set up the keypad codes. Patient with a very long list of residents."
- Devon Ingram"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one on the truck, and we were moving cars again inside an hour."
- Chris Gallagher