Gate Repair in Everman, TX
A gate that won’t close in Everman usually means a post torqued out of plumb by Blackland Prairie clay, a hinge seized from summer heat, or a motor strained past its limits. Most repairs run $180-$450 and are finished in a single visit. Call (833) 754-7503 and a live person will pick up, day or night.
Ironworks Gate Co. works on the gates Everman actually has: utilitarian wood and chain-link swing gates that see hard daily use on streets where the soil moves underneath everything. We settle on the price before turning a single bolt, and every job is covered by our written 90-Day Done Right Promise.
Why Everman Homes Are Different
Everman sits squarely on North Texas’s Blackland Prairie, where expansive clay soils heave during wet winters and spring rains, then shrink hard in summer drought. That cycle torques gate posts out of plumb within a year or two, causing gates to bind, sag, and fail to latch. On older residential streets throughout 76140, cedar privacy gate posts were commonly set with shallow concrete collars that don’t reach through the active clay layer, so they rock and twist after just a few wet-dry cycles. Add summers that routinely exceed 100°F, warping wooden frames and accelerating rust, and the back-and-forth between extreme heat and occasional hard freezes compresses the lifespan of every gate component.
Gate Repair in Everman
Gate repair in Everman typically costs $180-$650 depending on the problem. Hinge and latch adjustments are usually done same-day, while full post resets with deeper footings run $400-$650. The difference is almost always in the soil, not the hardware. We see the same pattern on Bishop Street and West Ash: a gate that sagged after one wet spring, got adjusted, then sagged again the next year. The fix that holds is resetting the post below the active clay layer, not tightening another hinge.
For a closer look at how we approach these repairs, see Gate Repair.
Post Repair
This is the repair we perform most often in Everman. Blackland Prairie clay expands when wet and shrinks in drought, exerting tremendous force on posts set in shallow concrete. Within a year or two, the post tilts, the gate binds, and the latch misses. A post reset with deeper footing in Everman runs $350-$650 depending on how deep we need to go and what equipment can reach the site.
Hinge Repair
North Texas summers above 100°F warp wooden gate frames, and that stress concentrates at the hinges. On metal gates, the same heat accelerates rust on hardware that was never galvanized properly. Hinge repair in Everman runs $150-$280 for standard strap or T-hinge replacement, or $280-$420 if we’re welding new hinge mounts to a twisted frame. We stock heavy-duty galvanized and stainless hardware sized for the heavier gates common in this area.
Why do my gate posts keep leaning in Everman?
Everman’s expansive black clay soil swells when wet and shrinks during drought, torquing posts set with shallow concrete collars out of plumb. The permanent solution is pulling the posts and resetting them with footings that reach 30 inches or deeper, below the active clay layer. Call (833) 754-7503 for a free assessment, and we’ll tell you straight what your posts need.
Gate Installation in Everman
Gate installation in Everman typically runs $2,800-$6,500 for a standard automated driveway gate, with most projects completed in one to two days and backed by our written 90-Day Done Right Promise. If you’re tired of wrestling a sagging wooden gate on a 1970s ranch near Patton Avenue, a new installation is often the better long-term answer. We build for this soil and this climate. See Gate Installation for the full scope of what we install.
Swing Gate Installation
Swing gates fit the modest setbacks and level driveways typical of Everman’s 1960s-1990s housing stock. But a swing gate fails fast here if the posts aren’t set below the active clay layer. We set new posts on 48-inch-deep footings and use adjustable hinges that absorb minor seasonal movement. A manual swing gate installation in Everman typically costs $2,800-$4,200, with automation adding to that range.
Double Gate Installation
Double gates solve the width problem for two-car driveways without the sweep radius of a single long leaf. The challenge is synchronization: both leaves must meet dead level at the center, which becomes impossible if one post heaves even an inch. Double gate installation in Everman runs $3,200-$5,800 depending on automation and materials.
Can I repair my 1980s cedar gate or should I install a new one?
Most 1980s cedar gates in Everman have exceeded their service life. The wood has warped, the frame has twisted, and replacement lumber won’t match the original dimensions. If the frame is racked or rotted, a new aluminum or steel gate costs less over time than repeated repairs. Call (833) 754-7503 for an honest assessment, estimates are free.
Gate Motor & Opener in Everman
Gate motor and opener repair in Everman runs $180-$650 depending on the fix, and most jobs are completed same-day. If your motor hums but won’t move, grinds against a warped frame, or quit after the last hard freeze, we can usually diagnose it on the spot. We’re trained and equipped on nine major brands, including LiftMaster, FAAC, and BFT. See Gate Motor & Opener for details on the brands and systems we service.
Motor Repair
Most gate motor repairs in Everman fall between $180 and $480. Common fixes include replacing stripped clutch assemblies, failed start capacitors, and limit switches that lost their position after a power surge. After Winter Storm Uri in February 2021, we replaced dozens of capacitors across 76140 that blew when ice-locked gates tried to cycle against frozen tracks. We also see motors burned out from working against misaligned gates, the motor draws excessive amperage and fails. A $220 alignment and hinge service often saves a $900 motor.
Motor Installation
New gate motor installation in Everman runs $850-$2,400 for most residential swing and slide systems, including mounting hardware, safety sensors, and basic programming. Before we quote a motor, we check the gate’s structural squareness. A motor installed on a gate with heaved posts will fail early, no matter how well it’s built.
Is battery backup really necessary for gate openers in Everman?
Yes, if you need your gate to open when the power is out. Everman sits in Tarrant County’s severe weather corridor where thunderstorms, ice storms, and grid strain cause multiple outages yearly. Battery backup runs $280-$450 installed and provides 8-24 open-and-close cycles. Call (833) 754-7503 to discuss your setup.
Gate Access Control in Everman
Gate access control repair and installation in Everman typically runs $280-$650 for most keypad, remote, or smart access jobs. When your keypad quits after a spring rain or your remote stops talking to the gate, the problem is often at the post, not the electronics. We check post plumb before mounting any new unit. See Gate Access Control for the full range of access systems we install and repair.
Keypad Entry Systems
A good keypad should last ten to fifteen years, but on Everman gates, we see them fail sooner when the post shifts. A tilted post puts sideways stress on the housing, cracking the seal and letting moisture into the circuit board. Keypad repair or replacement in Everman runs $180-$340, and we always check post plumb before mounting a new unit.
Phone Entry Systems
Phone entry lets visitors call your home or cell from the gate. It’s one of the most cost-effective upgrades for Everman’s aging chain-link swing gates. We’ve retrofitted phone entry onto gates that were installed in the 1970s with nothing but a manual latch. Phone entry system installation in Everman runs $420-$780.
Why does my gate keypad keep losing connection after heavy rain in Everman?
Water is getting into the housing, usually because clay-heave tilt has cracked the seal or pulled the wiring conduit loose. We dry and test the board, reseal or replace the housing, and check post plumb so it doesn’t happen again. Call (833) 754-7503 for an exact quote, estimates are free.
Gate Parts & Welding in Everman
Gate parts and welding in Everman runs $180-$650 depending on whether you’re resetting a heaved post, replacing corroded hinges, or fabricating custom steel braces for a warped cedar gate. Most repairs are completed in a single visit, with upfront pricing settled before we start. See Gate Parts & Welding for what we can build and fix on-site.
Hinge Replacement
Original hinges on Everman’s 1970s through 1990s gates weren’t built for North Texas extremes. Repeated 100°F summers cook the grease out of steel hinges, and ice storms like February 2021’s Winter Storm Uri seize and crack them. A typical hinge replacement in Everman runs $180-$320 for a standard swing gate, including removal of the corroded hardware and installation of heavy-duty greasable hinges rated for the gate’s actual weight.
Post Replacement
Post replacement is where Everman’s black clay soil makes gate work a specialty trade. On older residential streets, cedar privacy gate posts were commonly set with shallow concrete collars that don’t reach through the active clay layer. Post replacement with a deeper footing in Everman runs $350-$650. We pull the old post, excavate to 30 inches or more below the active layer, and pour a proper footing that resists seasonal movement.
Can you weld a patch onto a 1990s chain-link gate that snapped during an ice storm?
Yes, if the surrounding frame is structurally sound. We cut out the damaged section, sleeve or splice with matching tubing, and weld to restore tension and alignment. If the frame is too far gone, we’ll tell you straight and quote replacement. Estimates are free, call (833) 754-7503.
Brands We Service in Everman
We’re trained and equipped on nine gate-automation brands, including LiftMaster, FAAC, BFT, Linear, Viking, and Ghost Controls, and we stock common components for fast turnaround in Everman. That means the correct fix on the first visit, whatever is on the driveway. Learn more about our brands.
Pricing for Gate Repair in Everman, TX
| Service | Typical range in Everman |
|---|---|
| Hinge repair or replacement | $150 - $280 |
| Gate realignment (posts stable) | $180 - $320 |
| Weld repair (mobile, on-site) | $200 - $380 |
| Post reset with deeper footing | $350 - $650 |
| Automation motor repair | $220 - $480 |
| Full automation motor replacement | $650 - $1,400 |
What moves the price in Everman: footing depth, equipment access, whether the gate is wood or metal, and whether automation components are involved. Every price is quoted and agreed before any work starts, a square deal, no surprises on the bill.
Neighborhoods We Serve in Everman
We respond to calls across Everman’s 76140 ZIP code, typically arriving within the hour for urgent repairs. Our crews know the streets and the soil.
- Everman Park area, older cedar privacy gates with common post-heave issues
- Bishop Street corridor, mid-century ranches with original chain-link
- South Hulen Street, mixed housing stock with frequent automation retrofit calls
- Trammel Davis Road, working-class homes with heavy-daily-use gates
Service Area - Cities Near Everman
While this page focuses on Everman, our crews also serve homeowners in surrounding Tarrant County communities. If you live just over the city line, we likely cover your street too: Rendon, TX, Kennedale, TX, Forest Hill, TX, Burleson, TX, and Crowley, TX. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office; crews serve Everman locally.
Serving Everman, TX - Our Local Coverage Area
Ironworks Gate Co. crews serve Everman and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Everman coverage area; if your address is on it, we can help.
Also serving nearby: Rendon, TX, Everman, TX, Kennedale, TX, Forest Hill, TX, Burleson, TX, Crowley, TX.
FAQs About Gate Repair in Everman
For urgent repairs, we typically arrive within the hour across Everman’s 76140 ZIP code. Same-day service is available for most gate repairs when you call before midday. A live person answers the phone 24 hours a day, 7 days a week. Call (833) 754-7503 and we’ll give you a straight arrival window.
Most gate repairs in Everman don’t require a permit. New automated driveway gate installations may, depending on the scope and electrical work involved. We’ll tell you during the estimate whether your project needs a permit and we handle the paperwork when it does. Call (833) 754-7503 for specifics on your property.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Everman Customers Say
"The hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a new gate, which two other companies had pushed for."
- Megan Whitaker"Reprogrammed every clicker in the community and set up the keypad codes. Patient with a very long list of residents."
- Devon Ingram"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one on the truck, and we were moving cars again inside an hour."
- Chris Gallagher