Fast, Reliable Gate Parts & Welding Across Kennedale
Gate parts and welding repair in Kennedale typically runs $180-$650 depending on whether you need a hinge reset, post replacement, or full custom fabrication, and most jobs are completed in a single visit with upfront pricing settled before we start. We answer our phones live 24 hours a day, 7 days a week at (833) 754-7503, and our technicians are usually on-site in Kennedale within hours, not days.
We’ve been working in Kennedale since before the subdivisions along Kennedale Kennel Road filled in, back when most of our calls came from acreage properties with working pipe gates. That history matters. Kennedale’s not Arlington. The ground here is Blackland Prairie clay that swells, cracks, and shifts with every season. A gate post that held firm in May can lean three inches by August. We know which roads still have caliche under the topsoil, which gates were set by landowners in the 1980s without concrete footings, and what it takes to fix them so they stay fixed. Our Gate Parts & Welding team carries the heavy-duty hinges, adjustable brackets, and welding equipment to handle ranch-grade pipe gates on the same truck we use for residential ornamental work. One trip. Done right. Backed in writing.
Why Ironworks Gate Co. Is Kennedale’s Preferred Gate Parts & Welding Company
Ironworks Gate Co. has served the Kennedale area for over 42 years, founded in 1984. In that time we’ve reset posts on properties near the old Kennedale High School, welded new hinge brackets for ranchettes off Little School Road, and replaced operators in the newer subdivisions near 287. Our customers here remember the last contractor who didn’t show, or showed without the right parts, or left a gate worse than they found it. We don’t do that. A square deal: upfront price, no surprises on the bill.
Our reviews from Kennedale homeowners consistently mention the same things. The technician arrived when promised. He had the parts on the truck. He explained what was wrong before touching a bolt. And when a post reset settled slightly after the next big rain, we came back and adjusted it under our 90-Day Done Right Promise, no paperwork, no arguing. That’s the Keystone Standard. It applies to every gate job we do in 76060.
Response time to Kennedale is typically same-day or next-morning, because our technicians live and work in the mid-cities corridor. We don’t dispatch from Dallas or Fort Worth. We’re already nearby. And because we’re trained and equipped on nine gate-automation brands, including FAAC, BFT, and Viking, we don’t make two trips for parts we should have carried the first time.
Our Gate Parts & Welding Services in Kennedale
Hinge Replacement
Heavy pipe gates on Kennedale acreage properties destroy standard hinges. The weight, the wind load across open prairie, and the constant stress of a gate that sags and binds all accelerate wear. We stock adjustable barrel hinges, j-bolt hinges, and custom-welded hinge brackets rated for gates up to 1,500 pounds. When we replaced the hinges on a ranch gate off Mistletoe Lane last spring, we also welded a reinforcing gusset plate to the gate frame because the original mounting point had wallowed out from years of sag. That’s the kind of thing you catch when you’ve done this work in Kennedale long enough to know what the clay does to a gate over twenty years.
Post Replacement
This is our most frequent call in Kennedale, and it’s almost always the same story. The original post was set in caliche without concrete, or the footing was poured too shallow for the expansive clay. After a wet spring, the post leans. After a dry summer, it leans worse. We dig to code depth, pour a proper concrete footing, and set a steel or treated wood post plumb and braced. On automated gates, we also verify operator alignment and limit-switch positioning, because a post that shifts even an inch can throw off the entire system. We swapped a failed lift on a heavy-duty ranch gate off Kennedale Mistletoe Lane, where the original posts were set in caliche and had shifted 4 inches from the seasonal clay cycle. We poured concrete footings to code depth, re-plumbed the gate, and welded a new adjustable hinge bracket to keep it square through the next drought.
Rail Repair
Bent or broken rails are common on Kennedale’s older welded pipe gates, especially where livestock have rubbed or pushed against them, or where a vehicle made contact on a narrow ranch entry. We straighten rails when possible and cut out and weld replacement sections when the damage is too severe. We match the original wall thickness and finish, so the repair doesn’t look like a repair. On ornamental iron gates in Kennedale’s newer subdivisions, we also address the rust that starts at rail-to-picket welds, grinding back to clean metal and re-welding with proper penetration.
Custom Welding
Not every Kennedale gate fits a catalog part. We fabricate custom hinge brackets, latch keepers, and operator mounting plates in our mobile welding rig, right on your property. Last fall we built a custom rolling gate carrier for a Kennedale customer whose driveway slope meant a standard V-groove roller wouldn’t track properly. We measured, cut, and welded a solution that afternoon. That’s the advantage of a company that still has welding craft in-house, not just parts-changers.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kennedale
We carry parts and provide certified service for nine major gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Kennedale customers, this means we don’t order parts and make you wait. Our trucks are stocked with common FAAC and BFT control boards, Viking limit switches, and Linear actuator hardware. When your operator fails on a Saturday evening, we can often replace the failed component that same visit. No “we’ll come back next week with the part.” We know the local suppliers in the DFW mid-cities, and we maintain our own inventory for the brands we see most often in this market.
Common Gate Parts & Welding Problems We See in Kennedale Homes
- Gate posts set in caliche or shallow footings lean and misalign after wet-dry clay cycles. Kennedale’s Blackland Prairie soil swells with rain and shrinks in drought, exerting tremendous lateral force on any post without a proper concrete footing below the frost and clay-active zone. We see this on properties along Kennedale Kennel Road and throughout the older ranchette areas.
- Oversized heavy gates on acreage properties wear out standard hinges and rollers prematurely. A 16-foot pipe gate weighing 800 pounds needs hardware rated for the load. When a landowner installs residential-grade hinges on a ranch gate, they bind, sag, and eventually tear out of the frame. We upgrade to commercial-duty hardware and weld reinforcement as needed.
- Automated operators on long driveways lose range and fail to cycle due to heat-degraded lubricants. Kennedale’s summer temperatures above 100°F bake the grease in sliding gate tracks, causing metal-on-metal binding that overloads the operator. We clean, re-lubricate with high-temperature synthetic grease, and inspect track alignment.
- Original welded pipe gates from the 1970s-1990s develop rust-through at weld points and rail connections. These gates were built to last, but decades of Texas sun and occasional ice exposure take their toll. We grind out failed welds, replace compromised sections, and re-weld with modern wire and technique for another generation of service.
Pricing for Gate Parts & Welding in Kennedale, TX
Here’s what gate parts and welding work costs in the Kennedale market. These are real ranges based on jobs we’ve completed in 76060, not national estimates.
| Service | Typical Range in Kennedale |
|---|---|
| Hinge replacement (standard residential) | $180-$280 |
| Hinge replacement (heavy-duty/ranch gate) | $320-$480 |
| Single post reset with concrete footing | $450-$650 |
| Post replacement (automated gate, includes rehang and alignment) | $580-$850 |
| Rail repair (straighten or section replacement) | $220-$400 |
| Custom welding (on-site fabrication) | $180-$350 per hour, most jobs 1-2 hours |
| Gate roller/carriage replacement | $200-$340 |
| Latch and lock replacement | $160-$260 |
What moves the price? Post depth and soil conditions are the biggest variables in Kennedale. Caliche or rock requires more labor to dig to code depth. Gate weight affects hardware cost. And accessibility matters: a gate at the back of a ten-acre property takes longer to reach than a suburban driveway. We give you an upfront, written price before we start. No surprises on the bill. Call (833) 754-7503 for a free estimate, and remember our standing offers: $50 off any repair over $250, a free second opinion on any written estimate, and our $89 seasonal tune-up to catch problems before they become expensive.
We Also Serve Cities Near Kennedale
Our service area covers the full mid-cities corridor. We regularly handle Gate Parts & Welding in Kennedale and also respond to calls in Everman, Rendon, Forest Hill, and Arlington. The same technicians, the same stocked trucks, the same 90-Day Done Right Promise apply whether you’re on a half-acre lot in Forest Hill or a ranchette near Rendon. If you’re unsure whether we cover your address, call and ask. A live person will answer.
Serving Kennedale, TX - Our Local Coverage Area
We’re based in the Kennedale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kennedale
The expansive black clay soils of the Blackland Prairie swell dramatically when wet, exerting lateral pressure against any post without a proper concrete footing sunk below the active clay zone. Many older Kennedale properties had posts set in caliche or shallow holes without concrete, a shortcut that works until the first serious wet-dry cycle. We reset posts to code depth with poured concrete footings, which eliminates the lean in most cases. Call (833) 754-7503 for a free evaluation of your post condition.
Yes, and we do this regularly on Kennedale’s older ranch gates. Sagging usually means the original hinge mounting point has wallowed out or the hinge itself was under-rated for the gate weight. We grind back to clean metal, weld a new reinforced hinge bracket or mounting plate, and often add a gusset for additional strength. We match our welding technique to the original pipe wall thickness so the repair integrates cleanly. Most heavy-gate hinge repairs in Kennedale run $320-$480. Call for an exact quote.
Heat-degraded lubricant in sliding gate tracks is the leading cause of summer failure we see in 76060. When grease breaks down above 100°F, metal rollers bind in the track, overloading the operator until it faults out or burns up its control board. We clean the track, replace worn rollers, and re-lubricate with high-temperature synthetic grease rated for Texas summers. We also see failed limit switches and dry capacitors in operator housings that bake in direct sun. Our $89 seasonal tune-up catches these issues before they cause a complete failure.
Yes. Kennedale’s semi-rural character means we regularly service H-brace pipe gates that are still working livestock facilities, not just driveway ornaments. We replace failed lift cables, reset leaning posts, weld new hinge pins, and upgrade latches to keep these gates functional and safe. When a landowner wants to retain the gate’s agricultural character while adding automation, we can often adapt a residential operator to the existing frame with custom welding and bracket fabrication. We’ve done this on properties throughout southern Kennedale.
It depends on the gate’s condition and your daily usage. If the frame is sound and the posts are properly set, automation is straightforward and typically costs $1,800-$3,400 for a standard swing or slide operator installation in Kennedale. If the gate is already sagging, rusted through at welds, or set on failing posts, we recommend repairing the structure first. Many Kennedale homeowners in developing areas choose this upgrade as acreage subdivides, replacing manual agricultural gates with keypad or remote-access systems for convenience and security. We’ll give you an honest assessment of your gate’s readiness. Call (833) 754-7503 for a free estimate.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Kennedale since 1984.