Fast, Reliable Gate Parts & Welding Across Colleyville
Gate parts and welding repair in Colleyville typically runs $180-$1,800 depending on scope, with most hinge and rail jobs completed same-day and full post-reset work done in a single visit. We’re usually on-site in Colleyville within 90 minutes of your call, and our crews travel with welding rigs, concrete tools, and a mini-excavator trailer for the heavy-duty estate work this city demands.
Colleyville’s 76034 zip is built different from its neighbors. The large private lots off Glade Road, Pleasant Run Road, and throughout the Colleyville Nature Center area carry gates that outweigh what you’ll find in Bedford or Hurst by a factor of three. These are 10-foot ornamental iron leaves on 1990s operators, farm paddock gates for equestrian properties, and estate entries that have taken 25 years of North Texas clay heave. When a Colleyville homeowner calls, they need someone who shows up once and handles the full scope: post reset, parts, welding, and automation. That’s what our Gate Parts & Welding team has done here for over four decades. Call (833) 754-7503.
Why Ironworks Gate Co. Is Colleyville’s Preferred Gate Parts & Welding Company
We’ve worked Colleyville since 1984, long before the current wave of estate development filled in the acreage west of Highway 26. Our technicians know the difference between a 1992 Viking operator on a Glade Road estate and a 2010 Ghost Controls system in a newer infill lot, and they pack parts for both. The 90-Day Done Right Promise applies to every job in Colleyville, written and with no paperwork to chase down.
Colleyville customers tell us the same thing: the last guy fixed the hinge but ignored the post tilt, so the gate dragged again in six months. We don’t do half jobs. Our crew carries a mini-excavator trailer for exactly the scope that Colleyville’s clay soil demands, and we settle on upfront pricing before turning a single bolt.
A live person answers our phones 24 hours a day, 7 days a week. Not a voicemail tree. Not an answering service. When your estate gate won’t close at 9 p.m. and your horses are in the pasture, that matters.
Our Gate Parts & Welding Services in Colleyville
Post Replacement & Realignment
This is the dominant repair in Colleyville, and it’s not even close. The shrink-swell clay throughout Tarrant County pulls concrete footings out of plumb every summer drought and heaves them back every wet winter. On a 2-acre estate off Glade Road, we arrived to replace a worn hinge on a 1990s DoorKing 6000 system, but found the gate post tilted 3 degrees from clay heave. We drove a new concrete footer, re-hung the 10-foot-tall ornamental iron leaf, and installed a fresh control board-all in one trip, because our crew carries a mini-excavator trailer for exactly this Colleyville-common scope. Post replacement in Colleyville typically runs $650-$1,400 including concrete, rehang, and alignment.
Custom Welding
Colleyville’s ornamental iron gates, many original to 1980s and 1990s builds, develop stress cracks at weld points after decades of clay-soil movement and periodic ice storm loading. We MIG and TIG weld on-site, matching existing profiles on decorative scrollwork and reinforcing structural joints on heavy farm gates. Our welders are also certified automation technicians, so they won’t torch through a control wire you didn’t know was there. Custom welding repair in Colleyville generally falls between $220-$580 depending on access and material thickness.
Hinge Replacement
Heavy estate gates on tilted posts destroy hinges fast. We see this constantly in Colleyville’s older neighborhoods: the homeowner replaces the hinge twice, then calls us when the gate still won’t latch. The real fix is resetting the post first, then installing a heavy-duty ball-bearing hinge rated for the actual gate weight. We stock hinges for gates up to 1,500 pounds because Colleyville’s properties demand it. Hinge replacement with proper post alignment runs $180-$340 in Colleyville.
Rail Repair & Gate Rollers
Oversized estate gates on aged operators over-stress gate rollers and rails, causing welds to crack under ice-storm loads. We replace worn rollers with heavy-duty sealed-bearing units, repair or replace bent track, and reinforce rail attachments. For the 12-foot-plus swing gates common off Pleasant Run Road and near the Colleyville Nature Center, we carry rollers rated for continuous duty cycles that standard hardware store units won’t survive. Rail and roller work in Colleyville typically costs $280-$620.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Colleyville
We maintain local parts stock and factory-trained certification on nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Colleyville specifically, we see a lot of Viking and Linear operators from the 1990s estate buildouts, plus DoorKing 6000 series units that have outlasted three generations of lesser hardware. We carry replacement control boards, limit switches, and gear assemblies for these legacy systems because ordering from California costs Colleyville homeowners a week they don’t have. Our turnaround on parts we don’t stock is 24-48 hours through our Dallas-Fort Worth supply chain.
Common Gate Parts & Welding Problems We See in Colleyville Homes
- Clay-soil heave tilts gate posts so severely that replacement hinges no longer align with latch strikes. We’ve measured posts leaning 4 degrees off plumb in Colleyville’s 76034 zip, where summer drought pulled soil away from footings and winter moisture caused upward heaving. The hinge swap won’t hold until the post is reset.
- Oversized estate gates on aged operators over-stress gate rollers and rails. A 12-foot ornamental iron leaf weighs 800-plus pounds. After 25 years of clay movement and ice storm shock loads, the welds at rail attachments crack. We repair the metal and upgrade the rollers to handle the real weight.
- Shrink-swell cycles fracture buried conduit to underground operators. Colleyville’s clay doesn’t just move posts; it shifts and crushes PVC conduit carrying 110V to slide gate operators. We trench, replace with rigid conduit, and seal penetrations against the next cycle.
- 1990s control boards fail after decades of voltage fluctuation and heat cycling. The original Viking and Linear boards in Colleyville’s estate homes weren’t built for 30 Texas summers. We stock replacements and can often swap a board same-day.
Pricing for Gate Parts & Welding in Colleyville, TX
Here’s what Colleyville homeowners actually pay:
- Hinge replacement (with post alignment check): $180-$340
- Custom welding repair, on-site: $220-$580
- Rail and roller replacement: $280-$620
- Post reset with new concrete footer and rehang: $650-$1,400
- Full post replacement with excavation: $900-$1,800
- Control board replacement (DoorKing, Viking, Linear): $340-$680
What moves the number? Gate weight and height. Access for our mini-excavator trailer. Whether the post is shared with an intercom or camera system that needs temporary relocation. How deep the original footer was poured, and whether it’s intact enough to reuse. We settle on a firm price before starting, and that price includes the 90-Day Done Right Promise. No surprises on the bill.
Active offers for Colleyville: $50 off any repair over $250. Free second opinion on any written estimate. $89 seasonal tune-up. Permanent 5% senior and veteran discount. Call (833) 754-7503 for exact pricing on your gate.
We Also Serve Cities Near Colleyville
Our crews run daily routes through Bedford, Hurst, Southlake, and Euless, but Colleyville gets priority scheduling for heavy estate work because of the specialized equipment and scope we know to expect. If you’re on the border of 76034 and neighboring zips, we’ll confirm coverage when you call.
Serving Colleyville, TX - Our Local Coverage Area
We’re based in the Colleyville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Colleyville
Your gate post is tilting in the clay soil, not the hinge failing. Colleyville’s shrink-swell clay heaves and contracts seasonally, pulling concrete footings out of plumb. We reset the post with proper depth and drainage, then install a hinge rated for the actual gate weight. Call (833) 754-7503 and we’ll check post plumb as part of any hinge quote, estimates are free.
Yes, we stock replacement control boards for DoorKing 6000 series and can usually swap one same-day in Colleyville. These boards fail after decades of heat cycling and voltage fluctuation, and we see them regularly in Colleyville’s 1990s estate homes. Call (833) 754-7503 to confirm board availability for your specific model.
Yes, our welders carry MIG and TIG rigs and match existing ornamental profiles on location. We also check whether the crack stems from post tilt or impact damage, because welding without fixing the root cause means the crack returns. For a free on-site assessment in Colleyville, call (833) 754-7503.
It’s almost always post tilt from clay heave, especially on Colleyville’s equestrian properties where heavy gates sit on original footers from the 1980s or 1990s. We measure post plumb first; if it’s out more than 1 degree, we reset before touching hinges or rollers. Post reset and rehang for a 15-foot farm gate in Colleyville typically runs $750-$1,200. Call (833) 754-7503 for exact pricing.
Yes, we stock sealed-bearing rollers rated for gates up to 1,500 pounds and 14 feet wide, the size we regularly see on Colleyville estate properties off Glade Road and Pleasant Run Road. Standard hardware store rollers fail in months under this load. For roller sizing and installation in Colleyville, call (833) 754-7503, estimates are free.
Ready to get your gate working right? Call Ironworks Gate Co. at (833) 754-7503 for a free estimate. A live person will answer, 24 hours a day, 7 days a week. We’ll be there when we say, we’ll settle on a square price upfront, and we’ll stand behind it with the 90-Day Done Right Promise.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Colleyville since 1984.