Ghost Controls Gate Repair in Los Angeles, CA

Ghost Controls Gate Repair in Los Angeles: What to Know First

We provide independent Ghost Controls gate repair throughout Los Angeles, and most calls are handled same-day or next-day. A typical Ghost Controls repair runs between $195 and $485 depending on whether the issue is mechanical, electrical, or both, and we settle on an upfront price before touching a single bolt. This page is written for Los Angeles homeowners who bought a Ghost Controls operator for its DIY-friendly reputation and now need a gate specialist who understands how that system interacts with the actual gate hardware. If your Ghost Controls remote clicks but the gate does not move, or if the arm strains and reverses on a mild slope in the Hollywood Hills, we can diagnose it properly and fix it right. Call (833) 754-7503 - a live person answers, 24 hours a day, 7 days a week.

Call (833) 754-7503

How Ghost Controls Products Fail - and How We Fix Them

• ARCH Series arm seizes or slips in coastal zones. The ARCH-1 and ARCH-2 linear actuators use an aluminum housing that corrodes internally when exposed to Santa Monica or Marina del Rey salt air. The worm gear binds, the motor overheats, and the clutch slips. We strip the actuator, clean the drivetrain, and replace the internal clutch pack with a sealed aftermarket equivalent that holds up better than OEM near the ocean.
• TSS1XP or TDS2XP control board fails after heat waves. The single and dual solar-ready control boxes mount in direct sun on many Los Angeles driveway posts. After a July week over 95 degrees, we see capacitor swelling and relay contact pitting. We test the board, replace failed components where practical, or swap in a new board and relocate it to shaded mounting if the post geometry allows.
• GC GHOST sensor loop gives false obstruction readings. The magnetic vehicle sensor that ships with GC series kits is sensitive to interference from underground utilities common in older Los Angeles neighborhoods like Highland Park or Eagle Rock. We trace the loop, recalibrate sensitivity at the board, or replace with a direct-burial loop rated for EMI-heavy soil.
• Heavy iron gates overwhelm the DIY mounting hardware. Ghost Controls brackets are engineered for standard aluminum or light steel gates. On the wrought-iron driveway gates common in Los Feliz or Hancock Park, the bracket flexes, bolts wallow out, and the gate sags. We fabricate custom steel gusset plates, weld reinforced mounting pads, and realign the gate so the actuator geometry is correct.
• Battery systems drain prematurely on north-facing slopes. Solar panels on Ghost Controls kits need direct sun to keep the 12V battery charged. In the canyons - Laurel, Topanga, parts of the Palisades - shaded drives mean dead batteries by November. We calculate actual load versus panel output, upgrade to higher-capacity AGM batteries where needed, and advise honestly when a hardwired 110V supply makes more sense than chasing solar in a dark driveway.

Our Ghost Controls Gate Repair Process

1. 1
   A live person takes your call. No voicemail, no callback queue. We ask what the gate is doing, what it is not doing, and whether you know the Ghost Controls model. We schedule a window and confirm it.
2. 2
   Diagnosis on arrival. Our tech tests the control board, actuator draw, safety loops, and gate mechanicals separately. We isolate whether the problem is the Ghost Controls system, the gate itself, or the interaction between them.
3. 3
   Parts decision with you. If the board is fried, we explain OEM versus quality aftermarket options and what each means for your warranty status. No part gets ordered without your okay.
4. 4
   The repair. We weld, align, replace, or reprogram as needed. Most Ghost Controls jobs finish in one visit because our trucks stock common actuators, boards, and hardware.
5. 5
   Full-cycle testing. We run the gate through open, close, obstruction reverse, and manual release. We check force settings against UL 325 standards.
6. 6
   Written guarantee and cleanup. You get the 90-Day Done Right Promise, the Keystone Standard, in writing. We leave the driveway cleaner than we found it.

What Ghost Controls Gate Repair Costs in Los Angeles

These are real ranges we have quoted in Los Angeles this past year for Ghost Controls systems:

• Sensor recalibration or loop replacement: $195-$275
• Actuator rebuild or clutch replacement: $285-$395
• Control board replacement (OEM): $340-$485
• Custom bracket fabrication and weld repair for heavy gates: $395-$650
• Full gate realignment with Ghost Controls reinstallation: $450-$780

What moves the price: gate material and weight, access to the post or pad, whether the gate itself needs welding or hinge work in addition to the operator, and whether we use OEM Ghost Controls parts or quality aftermarket equivalents. We do not start work until you approve the exact price. Estimates are free. Call (833) 754-7503.

Why Los Angeles Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We are an independent Ghost Controls service provider, not a factory-authorized dealer, which means we fix what actually broke rather than what a warranty flowchart suggests. Our techs carry nine brands of automation parts, including LiftMaster, Mighty Mule, and DoorKing, so if your Ghost Controls system is beyond practical repair, we can recommend and install a replacement that fits your gate without upselling what you do not need. Victor Salinas started this company in 1984, and the 90-Day Done Right Promise applies to every job - written, no paperwork, no arguing. A live person answers the phone at midnight on Sunday. Background-checked, uniformed technicians show up when we say. That is the square deal.

FAQs