Gate Repair in Burbank, CA
Gate repair in Burbank typically costs $180-$650 depending on what has failed, and most jobs are completed in a single visit with upfront pricing agreed before any work begins. Burbank gates fail differently than gates in neighboring cities. Hard water corrodes hardware faster, Santa Ana winds warp panels and strip hinges, and gates near the studio corridors in 91505 and 91506 cycle dozens of times daily instead of the typical four to six. Call (833) 754-7503 and a live person answers, 24 hours a day.
Why Burbank Homes Are Different
Burbank sits deep in the San Fernando Valley where Santa Ana winds funnel through the Cajon and Newhall passes and regularly gust to 50-70 mph across the valley floor. We plan our autumn-to-winter schedule around the surge of emergency calls that follows: warped aluminum panels, hinges stripped from posts, operators burned out from fighting wind load. The housing stock compounds this. Burbank’s residential core is dominated by post-WWII ranch homes and bungalows built from the late 1940s through the 1960s, many with wrought-iron or tubular steel gates added decades later that are now aging out simultaneously. Steeper lots on the south-facing Verdugo foothill edges create sharper driveway grades that accelerate wear on operators and ground tracks. Burbank Water and Power delivers water with notably high mineral content, and sprinkler overspray on gate posts turns those minerals into an accelerant for rust.
Gate Repair in Burbank
Gate repair in Burbank means diagnosing problems that are specific to this valley: wind fatigue, mineral corrosion, and high-cycle operator burnout near the studio districts. Most repairs run $180-$650, and we quote the exact price before turning a single bolt. A live person answers our phones 24 hours a day, 7 days a week at (833) 754-7503, and our technicians typically reach Burbank homes within 45 minutes to an hour from dispatch. Our full Gate Repair service covers hinges, posts, welds, realignment, rust treatment, locks, and operator diagnostics.
Hinge Repair
Burbank Water and Power delivers mineral-laden water that accelerates corrosion on exposed steel hardware, and when sprinkler systems wet gate posts daily, that corrosion moves fast. We see seized hinges on ranch-home gates near Olive Avenue and Reese Place that should have lasted another decade. Typical hinge repair in Burbank runs $180-$320, including removal of the damaged hardware and installation of stainless or galvanized replacements that hold up to BWP’s water chemistry.
Post Repair
Gate posts in Burbank take abuse from two directions: Santa Ana winds funneling through the Newhall and Cajon passes at 50-70 mph, and the lateral strain of steep driveways in the Verdugo foothill neighborhoods like Country Club Estates. A post that leans even an inch throws off the entire gate geometry. Post repair in Burbank typically costs $280-$550 depending on access and whether the footing must be re-poured or the original post can be reinforced with welded steel.
Weld Repair
The wrought-iron and tubular steel gates added to Burbank’s post-WWII ranch homes in the 1970s through 1990s are reaching the end of their original weld life. Cracked joints at stress points, rust-weakened pickets, and broken scrollwork are common on homes between Magnolia Boulevard and Alameda Avenue. Our welders work in the field with portable MIG and TIG rigs, matching the original metal and finish. Weld repair in Burbank generally runs $220-$480 based on material and access.
How much does gate repair cost in Burbank?
Most gate repairs in Burbank run between $180 and $650, with hinge work at the lower end and motor replacement at the higher end. The price is settled before work begins, so there are no surprises on the bill. Call (833) 754-7503 for an exact quote on your gate. Estimates are free.
Gate Installation in Burbank
Gate installation in Burbank typically runs $2,800-$7,500 for most residential jobs, with swing gates on level lots at the lower end and custom automated sliding systems on hillside properties climbing higher. Most Burbank installations are completed in one to two days, with automation programming and final inspection wrapped up before we leave your driveway. Our Gate Installation team sizes every post footing, hinge, and operator for the wind loads this valley sees.
Swing Gate Installation
Swing gates remain the most common style in Burbank’s flatland neighborhoods, particularly in the post-WWII ranch home areas between Olive Avenue and Victory Boulevard. A single swing gate in Burbank typically costs $2,800-$4,200 installed, while a double swing system runs $3,800-$6,500 depending on automation and materials. We install swing gates with proper post depth and concrete footings rated for Santa Ana wind loads, and we verify that your driveway grade will not cause the gate to drag before we quote.
Sliding Gate Installation
Sliding gates are the practical choice for Burbank’s narrower driveways and steeper lots, particularly in the hillside areas above Glenoaks Boulevard and along the south-facing Verdugo slopes. A residential sliding gate installation in Burbank runs $4,200-$7,500, with the higher end covering heavy-duty steel frames, underground operators, and integrated access control. Steeper grades cause rolling friction to increase, which overheats operators and wears v-wheels prematurely. We calculate the exact grade and specify the correct operator horsepower before installation.
Do I need a wind-rated gate for my property in the Verdugo foothills?
Yes, if your property is exposed to prevailing winds. Burbank regularly sees 50-70 mph gusts during Santa Ana events, and hillside properties catch even stronger, more turbulent flow. A wind-rated gate has heavier gauge framing and reinforced hinges. Call (833) 754-7503 for a free on-site assessment of your exposure.
Gate Motor & Opener in Burbank
Gate motor repair in Burbank typically costs $180-$420, and most calls are completed same-day. Motors here fail from high-cycle use near the studio corridors, voltage spikes during valley heat waves, and the strain of fighting wind-warped gates. Our Gate Motor & Opener team is trained on nine brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the correct fix is made on the first visit.
Motor Installation
New gate motor installation in Burbank runs $850-$2,400 depending on gate weight, voltage requirements, and access control integration. We size the operator correctly for your gate’s cycle count, which matters more here than in most cities. A studio-neighborhood gate near Warner Bros. or Disney may cycle 30-50 times daily, far above suburban norms. We install for that reality, not a brochure spec.
Motor Repair
Motor repair is our most common Burbank call, with typical repairs running $180-$420. We see burned-out armature windings from high-cycle use, failed capacitors in older units, and controller boards damaged by voltage spikes during valley heat waves. Because we are trained and equipped on nine brands, we diagnose on the first visit and repair rather than replace when it makes sense.
How do Santa Ana winds affect gate motors in Burbank?
Santa Ana winds regularly hit 50-70 mph gusts in Burbank’s valley floor, warping gate panels and burning out operators that strain against misaligned loads. We see a reliable autumn-to-winter surge in emergency motor failures. Call (833) 754-7503 before the motor burns out completely. Estimates are free.
Gate Access Control in Burbank
Gate access control repair and installation in Burbank typically runs $340-$1,200 depending on the system, and most jobs are completed in a single visit with upfront pricing settled before work begins. The studio-corridor neighborhoods near Olive Avenue have an unusually high concentration of automated security gates, and homeowners there routinely need temporary codes for assistants, deliveries, and visiting production staff. Our Gate Access Control service covers keypads, remotes, phone entry, card readers, and video intercoms.
Keypad Entry Systems
Keypad entry in Burbank runs $380-$650 installed, with basic stand-alone units at the lower end and cellular-connected models with audit trails higher. Burbank’s hard water and sprinkler overspray will kill an unsealed keypad in three to four years. We mount ours with sealed housings and recommend stainless-steel backplates on wrought-iron posts.
Remote Control Programming
Remote programming or replacement in Burbank costs $85-$180 depending on whether we are syncing existing remotes or replacing a lost set and reprogramming the receiver. Many of the 1970s-1990s-era gates in Burbank’s ranch neighborhoods still run on single-button dip-switch receivers that are trivial to clone. We upgrade these to modern encrypted systems during service calls.
Why do my gate hinges rust faster in Burbank than in nearby Glendale?
Burbank Water and Power delivers water with notably high mineral content, and sprinkler overspray deposits those minerals on exposed steel. Glendale’s water chemistry does not produce the same mineral-crust buildup. We spec stainless steel hinges as standard on Burbank replacements. Call (833) 754-7503 for a free inspection and exact quote.
Gate Parts & Welding in Burbank
Gate parts and welding repair in Burbank typically runs $180-$650 depending on the component, and most jobs are completed in a single visit with upfront pricing settled before we start. Our Gate Parts & Welding service covers hinge replacement, post replacement, rail repair, roller replacement, and custom fabrication for gates that need more than a patch job.
Hinge Replacement
Hinges are the most common failure point on Burbank’s aging wrought-iron and tubular steel gates. The combination of hard-water mineral deposits and sprinkler moisture corrodes the pin and barrel years faster than in coastal cities. A typical hinge replacement in Burbank runs $180-$340 for a standard residential gate, including removal of the seized hardware and installation of a corrosion-resistant kit.
Post Replacement
In Burbank’s post-war ranch neighborhoods, original steel posts installed in the 1970s-1990s frequently lose structural integrity below the surface, where hard-water deposits and constant soil moisture create accelerated corrosion that is invisible until the gate starts leaning. Post replacement in Burbank typically costs $450-$650, including excavation, concrete work, and re-hanging the gate on a properly aligned new post.
Can you weld a broken latch on my 1980s wrought-iron gate near Warner Bros.?
Yes. We weld broken latch mounts and fabricate replacement components for aging wrought-iron gates throughout the 91505 and 91506 ZIPs near the studio district. We match existing profiles where possible and reinforce weak points that caused the original failure. Most welding repairs are completed in a single visit. Call (833) 754-7503 to schedule.
Brands We Service in Burbank
We service nine gate-automation brands in Burbank, including Viking, Ghost Controls, DoorKing, and Elite, with common parts stocked locally for same-day repairs. See our brands for the full list.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Hinge repair / replacement | $180 - $320 |
| Post repair / reset | $280 - $550 |
| Field weld repair | $220 - $480 |
| Gate realignment | $200 - $380 |
| Motor repair (parts + labor) | $180 - $420 |
| New motor installation (swing) | $850 - $1,800 |
| Keypad entry installation | $380 - $650 |
| Post replacement with concrete | $450 - $650 |
Steep driveway access, rust damage requiring multiple hardware replacements, and operator replacement on a high-cycle gate all push a Burbank job toward the higher end. Every price is quoted and agreed before any work starts. No surprises on the bill.
Neighborhoods We Serve in Burbank
Our trucks regularly cover Burbank’s residential neighborhoods, typically with same-day or next-day response from our Los Angeles dispatch.
- Magnolia Park
- Hillside District
- Media District / Studio Corridor
- Chandler Park area
- Country Club Estates
Service Area - Cities Near Burbank
In addition to Burbank, CA, we serve nearby communities including Universal City, CA, North Hollywood, CA, Glendale, CA, Valley Village, CA, and Studio City, CA. Call (833) 754-7503 to confirm coverage for your address.
Serving Burbank, CA - Our Local Coverage Area
Ironworks Gate Co. crews serve Burbank and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Burbank coverage area; if your address is on it, we can help.
Also serving nearby: Burbank, CA, Universal City, CA, North Hollywood, CA, Glendale, CA, Valley Village, CA, Studio City, CA.
FAQs About Gate Repair in Burbank
We typically reach Burbank homes within 45 minutes to an hour from dispatch, with same-day or next-day scheduling across the 91521, 91522, 91523, and 91526 ZIP codes. A live person answers our phones 24 hours a day, 7 days a week. Call (833) 754-7503 to schedule.
Most routine gate repairs, hinge replacements, and operator repairs do not require a permit in Burbank. New automated gate installations, significant electrical work, or structural post replacements may trigger Burbank Building and Safety review, particularly if the gate fronts a public sidewalk or alley. We flag any job that needs permitting before we begin and handle the paperwork where required. Call (833) 754-7503 to discuss your specific project. Estimates are free.
When your Burbank gate needs work, call Ironworks Gate Co. at (833) 754-7503. A live person answers. We give you an upfront price, do the job right, and back it in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Our slide gate had been dragging for months and getting worse. The chain was stretched and a guide roller had seized. Both replaced, and he reset the limits so it stops properly at each end now."
- Veronica Ramirez"The repair is holding. He was quite a bit later than the window I was given and the office did not call me about it, I had to call them. The work itself was done well once he arrived."
- Ruben Morales"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and put a surge protector on the line so hopefully it does not happen again."
- Layla Haddad