Fast, Reliable Gate Parts & Welding Across Lynnwood
Gate parts and welding repair in Lynnwood typically runs $180-$650 depending on whether you need a single hinge replaced or a full post reset with custom welding. Most calls in the 98036 and 98087 ZIP codes are completed same-day because our trucks carry cedar posts, galvanized hardware, and welding equipment for steel and aluminum gates.
We’ve been driving to Lynnwood since 1984. We know the difference between a 1970s ranch on 196th Street SW with original cedar privacy gates and a newer townhome off Alderwood Mall Parkway with an automated Viking or DoorKing system. That familiarity matters when you’re deciding whether a leaning gate needs a new post or a complete rebuild. Call (833) 754-7503 and a live person will answer, 24 hours a day.
Why Ironworks Gate Co. Is Lynnwood’s Preferred Gate Parts & Welding Company
Lynnwood homeowners don’t call us for flashy trucks or slogans. They call because their neighbor in the Brier area recommended us after we replaced three rotted cedar posts on a 1982 split-level, or because we welded a new hinge assembly on a steel driveway gate near Picnic Point that another company said needed complete replacement.
Our response time to Lynnwood averages under 90 minutes during business hours because our technicians start from dispatch points that cover Snohomish County. We don’t make you wait until Tuesday for a gate that’s sagging into your driveway.
Victor Salinas has built this company on the K.E.Y.S. code - Krafted right, Every time, Your home first, Standing behind it - and that applies whether we’re replacing a single latch in Alderwood Manor or fabricating a custom welded frame for an estate gate near Martha Lake. Every job carries our 90-Day Done Right Promise, written and with no paperwork to file.
Our standing offers apply in Lynnwood just as they do everywhere we serve: $50 off any repair over $250, a free second opinion on any written estimate you bring us, an $89 seasonal tune-up, and a permanent 5% discount for seniors and veterans.
Our Gate Parts & Welding Services in Lynnwood
Hinge Replacement
Steel hinges on Lynnwood gates corrode faster than almost anywhere we work. The marine air rolling in from Puget Sound, combined with salt spray off Highway 99, eats through standard zinc-plated hardware in 10-12 years. We see this constantly in the older subdivisions near 196th Street SW and 44th Avenue W, where gates installed in the 1990s are now hanging from rusted hinges that threaten to shear off.
We stock galvanized and stainless steel hinge sets sized for cedar, steel, and aluminum gates. A typical hinge replacement in Lynnwood runs $180-$320 for standard residential gates, including removal of the corroded hardware and proper alignment so the gate doesn’t bind. For heavier automated systems, we upgrade to ball-bearing hinges rated for the motor’s pull force.
Post Replacement
This is the repair we make most often in Lynnwood, and it’s the one that catches homeowners off guard.
In Lynnwood’s older subdivisions, cedar gate posts set in concrete collars decades ago are rotting from the inside at the concrete-soil interface. Moisture gets trapped between the post and collar with nowhere to drain. The visible above-grade wood often looks fine. The buried section has completely lost integrity. We’ve had gates that appeared structurally sound collapse when a child pushed on them.
Our technicians probe post bases on every job because this failure mode is that common. When we find it, we extract the old post and collar, set a new pressure-treated or cedar post in gravel for drainage, and pour a new concrete footing that sheds water. Post replacement in Lynnwood typically costs $380-$650 depending on depth, gate weight, and whether we need to temporarily brace an automated system. We recently completed this exact repair on a 1978 ranch near Scriber Lake Park where the post had rotted completely through at 14 inches below grade.
Rail Repair & Custom Welding
Steel gates in Lynnwood develop stress cracks at weld points where corrosion has weakened the metal. We don’t patch these. Our welders cut out the compromised section, fabricate a replacement piece from matching steel stock, and weld it with proper penetration and finish. A rail repair with custom welding runs $280-$480 for most residential gates.
We also fabricate entirely new steel frames for gates where the original is too far gone. This is common with 1980s ornamental steel gates in the Alderwood Manor area that have rusted through at the bottom rail. Building a new frame and hanging it on existing posts costs $650-$1,100, still far less than full gate replacement.
Gate Rollers
Sliding gates in Lynnwood’s wet climate suffer from seized roller bearings and corroded axles. We stock sealed-bearing nylon and steel rollers rated for marine environments. Nylon rollers run quieter and don’t rust; we recommend them for coastal properties. Roller replacement is $220-$380 for a standard residential sliding gate, including track cleaning and alignment.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lynnwood
Our trucks carry parts for Viking, Ghost Controls, and DoorKing openers, along with universal hardware that fits most gate systems. We’re also trained and equipped on FAAC, BFT, Linear, Elite, and Mighty Mule. This matters in Lynnwood because the newer townhome clusters near the Lynnwood Link light rail corridor are installing automated gates from multiple manufacturers, while the legacy 1960s-1980s housing stock often has older systems or no automation at all. We recently replaced a seized LiftMaster opener chain on a steel gate in a townhome cluster near the Lynnwood Link light rail station; the original chain had corroded through after only 8 years due to salt spray from Highway 99 and marine air. We installed a stainless steel chain and nylon rollers, and applied galvanized coatings to all hardware. Having the correct parts on the truck means we finish in one visit, not two.
Common Gate Parts & Welding Problems We See in Lynnwood Homes
- Cedar post rot at the concrete collar. The distinctive Lynnwood failure: moisture trapped between post and concrete rots the wood from inside, invisible until the gate leans or falls. We probe every post base we encounter.
- Steel hinge and latch corrosion. Ambient humidity and salt air destroy hardware in 10-12 years instead of 20. Homeowners in Picnic Point-North Lynnwood near the water see this accelerated even further.
- Automated opener chain failure. LiftMaster and FAAC chains corrode and seize in Lynnwood’s marine climate, often before the motor itself fails. We upgrade to stainless chains and coated hardware.
- Clay soil heaving concrete footings. Lynnwood’s glacial clay soils expand and contract with moisture, tilting posts and binding gates. Our post replacements account for this with deeper footings and proper drainage.
Pricing for Gate Parts & Welding in Lynnwood, WA
| Service | Typical Range in Lynnwood |
|---|---|
| Hinge replacement (single) | $180-$320 |
| Gate roller replacement (set) | $220-$380 |
| Rail repair with custom welding | $280-$480 |
| Post replacement (cedar, standard depth) | $380-$650 |
| Custom steel frame fabrication | $650-$1,100 |
These ranges reflect Lynnwood’s market specifically. Post replacement runs higher here than inland areas because of the depth required to get below the moisture-trapping clay layer and the frequency of automated gate attachments that need temporary bracing. We settle on an exact price before we start, and our $50 off any repair over $250 applies automatically. Estimates are free. Call (833) 754-7503.
We Also Serve Cities Near Lynnwood
Our Gate Parts & Welding in Lynnwood coverage extends to Alderwood Manor, Brier, Picnic Point, and Picnic Point-North Lynnwood. The same marine climate conditions apply throughout this corridor, and our trucks carry the same inventory of corrosion-resistant hardware and pressure-treated posts. If you’re unsure whether your address falls in our service area, call and we’ll confirm while you’re on the line.
Serving Lynnwood, WA - Our Local Coverage Area
We’re based in the Lynnwood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lynnwood
Moisture gets trapped between the cedar post and its concrete collar, rotting the wood from the inside at the soil line where you can’t see it. The above-grade portion stays solid-looking while the buried section turns to pulp. We probe post bases on every service call because this failure mode is so common in Lynnwood’s 1960s-1980s subdivisions. If your gate has any wobble or the latch no longer aligns, the post may be worse than it looks. Call (833) 754-7503 for a free inspection.
In Lynnwood’s marine environment, inspect gate rollers every 3-4 years and expect replacement every 6-8 years for steel rollers, 8-10 for sealed nylon. Salt air and humidity accelerate bearing corrosion and axle pitting. We include roller condition in our $89 seasonal tune-up. If your sliding gate is laboring or making noise, the rollers are likely due. Call for an exact assessment - estimates are free.
We can weld new hinge plates onto sound steel in most cases. We cut away the corroded metal, grind to clean steel, and fabricate a reinforcement plate that distributes load beyond the weak area. Full gate replacement is only necessary when the frame itself is perforated or the bottom rail has lost structural integrity. A typical welded hinge repair with reinforcement runs $280-$480. We’ll tell you honestly which side of that line your gate falls on.
Yes. We are trained and equipped on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The townhome clusters near the Lynnwood Link light rail station are installing mixed brands, and our Gate Parts & Welding team carries parts for all nine. We recently replaced a corroded LiftMaster chain on a steel gate near the station and upgraded it to stainless hardware rated for the coastal environment. Same-day service is standard for opener repairs in 98036 and 98037.
Marine-grade stainless steel or powder-coated aluminum locks outlast standard zinc-plated hardware by years. For cedar gates, we recommend locks with elongated strike plates that accommodate seasonal wood movement, and we always seal the mounting bolt holes to prevent water infiltration into the post. A quality lock installed correctly runs $180-$280. Avoid big-box locks with thin plating; we’ve replaced too many that seized after two Lynnwood winters. Call (833) 754-7503 and we’ll match a lock to your gate and your budget.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Lynnwood since 1984.